CCNA Practice exam questions part 1 (1-25)

7 What does the "IPX maximum-paths 2" command accomplish?

A. It enables load sharing on 2 paths if the paths are equal
metric paths.
B. It sets up routing to go to network 2.
C. It is the default for Cisco IPX load sharing.
D. It enables load sharing on 2 paths if the paths are
unequal metric paths.

Ans A


8 You want to enable both arpa and snap encapsulation on one
router interface. How do you do this?

A. The interface can handle multiple encapsulation types
with no extra configuration.
B. Assign two network numbers, one for each encapsulation
type.
C. Enable Novell-ether to run multiple encapsulation types.
D. Both arpa and snap are enabled by default so you don't
have to configure anything.

Ans B

8 By default, Cisco routers forward GNS SAPs to remote networks.
A. False
B. True

Ans A

9 To prevent Service Advertisements (SAPs) from flooding a
network, Cisco routers do not forward them. How are
services advertised to other networks?

A. Each router builds its own SAP table and forwards that
every 60 seconds.
B. Each router assigns a service number and broadcasts
that.
C. SAPs aren't necessary with Cisco routers.
D. Cisco routers filter out all SAPs.

Ans: A

10 Novell's implementation of RIP updates routing tables every
____ seconds.

A. 60
B. 90
C. 10
D. 30

Ans A



11 In Novell's use of RIP, there are two metrics used to make
routing decisions. Select the two metrics.


A. Ticks.
B. Hops
C. Loops
D. Counts


Ans:A &B




serial interface?


A. HDLC
B. SDLC
C. SAP
D. SNAP


Ans A


13 "arpa" is used by the Cisco IOS for which encapsulation
types?


A. Ethernet_II
B. Ethernet_802.3
C. Ethernet_802.2
D. Ethernet_SNAP


Ans A

14 "snap" is used by the Cisco IOS for which encapsulation

types?


A. Ethernet_SNAP
B. Token-Ring_SNAP
C. FDDI_SNAP
D. Novell-SNAP
E. Novell-FDDI.


Ans: A,B &C

15"sap" is used by the Cisco IOS for which encapsulation

types?


A. Ethernet_802.2
B. Token-Ring
C. FDDI_SNAP
D. Ethernet_802.3
E. FDDI_802.2


Ans A,B &E

16 Which type of Ethernet framing is used for TCP/IP and

AppleTalk?


A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP


Ans D


17 Which type of Ethernet framing is used for TCP/IP andDECnet?


A. Ethernet 802.3
B. Ethernet 802.2
C. Ethernet II
D. Ethernet SNAP


Ans: C


18 You are a system administrator on a NetWare network, you arerunning NetWare 4.11 and you cannot communicate with your
router. What is the likely problem?


A. NetWare 4.11 defaults to 802.2 encapsulation.
B. NetWare 4.11 defaults to 802.3 encapsulation
C. Cisco routers only work with NetWare 3.11.
D. NetWare 3.11 defaults to 802.2 encapsulation.


Ans A

19 NetWare IPX addressing uses a network number and a node

number. Which statements are true?


A. The network address is administratively assigned and can
be up to 16 hexadecimal digits long.
B. The node address is always administratively assigned.
C. The node address is usually the MAC address.
D. If the MAC address is used as the node address, then IPX
eliminates the use of ARP.


Ans A, C &D

20 Which NetWare protocol works on layer 3--network layer--of

the OSI model?
A. IPX
B. NCP
C. SPX
D. NetBIOS


Ans A

21Which NetWare protocol provides link-state routing?

A. NLSP
B. RIP
C. SAP
D. NCP


Ans: A

22 As a system administrator, you want to debug igrp but are

worried that the "debug IP igrp transaction" command will
flood the console. What is the command that you should
use?


A. debug IP igrp event
B. debug IP igrp-events
C. debug IP igrp summary
D. debug IP igrp events


Ans D


23 What does the following series of commands accomplish?router igrp 71

network 10.0.0.0

router igrp 109
network 172.68.7.0


A. It isolates networks 10.0.0.0 and 172.68.7.0.
B. It loads igrp for networks 109 and 71.
C. It disables RIP.
D. It disables all routing protocols.


Ans A

24 In the command "router igrp 109" what does 109 signify?

A. an autonomous system
B. any network number which the router is attached to
C. the allowable length of the routing table
D. the network socket number


Ans A

25 IGRP supports a feature that allows traffic to be

distributed among up to 6 (4 default) paths to provide
greater overall throughput and reliability. What is this
called?


A. unequal-cost load balancing
B. equal-cost load balancing
C. proportionate load balancing
D. low cost load balancing


Ans A

12 What is the Cisco name for the encapsulation type used on a